25 Cal Rifle Cleaning Kit with Cable

1. Not a one-size-fits-all kit — a .25-specific one. The .25 bore brush (copper-bronze wire), .25 cotton mop, and .25 brass patch puller are sized for .25 caliber rifle barrels, so the fit is right from the first pass.

2. 36 inches, end to end. The braided steel pull-through cable, with brass knurled ends and a weighted pull, covers the full length of a rifle barrel — one pull, clean bore.

3. The extras you would expect are here too. Double-ended nylon brush, 6-piece screwdriver bit set (PH1, PH2, slotted 4 & 7, Torx T15 & T20), brass connector for the screwdriver handle, and 25 pre-cut 1.5 x 3 in patches.

4. Stored, not scattered. The dark-green molded plastic case with transparent lid, hanging loop, and slide latches — every piece visible, from range bag to gun room.

5. From the factory that makes the brushes. Our own Ningbo brush factory, 20+ years in the industry (est. 2000), OEM partner to established US brands — dependable supply for wholesale.

Everything You Need to Clean Your 25 Caliber Rifle in One Case

Walk into any gun shop and the cleaning-kit wall is all common calibers — and the .25 owner walks out empty-handed. This 25 Cal rifle cleaning kit closes that gap: a .25 bore brush, mop, and patch puller matched to the barrel, a 36-inch cable that runs the full length of the bore, and the screwdriver bits and patches to finish the job, all in one dark-green case.

36-Inch Pull-Through Cable for Long Barrels

The 36-inch pull-through cable with black T-handle reaches through standard .25 caliber rifle barrels without a rigid rod, making field and range cleaning fast and simple. The cable is braided steel under a transparent protective sleeve, with brass knurled connectors at both ends and a weighted pull for a straight, even draw — enough reach for a full-length pass on any standard hunting rifle barrel.

.25 Cal Bore Brush and Mop

The .25 caliber bore brush (copper-bronze wire) and cotton mop are sized for rifle barrels, lifting powder fouling from bore and chamber without scoring the rifling.

Caliber note: every cleaning component in this 25 Cal rifle cleaning kit — the bore brush, the cotton mop, and the brass patch puller — is sized for .25 caliber rifle barrels. The 36-inch cable reaches the full length of a rifle barrel, short or long. Specific .25 cartridge names are not listed here because barrels vary by maker; if you are not sure your barrel is .25 caliber, measure the bore or send us your model before ordering — we will confirm compatibility.

Brass Patch Puller, Connector and 25 Patches

The brass patch puller holds standard 1.5 x 3 inch patches for a final dry pass, and the brass connector for the screwdriver handle is included with the set. The 6-piece screwdriver bit set (PH1, PH2, slotted 4 & 7, Torx T15 & T20) covers common rifle hardware — action and stock screws, sight screws, and scope-mount fasteners — for hand-tight maintenance, not for heavy torque.

Materials & Craftsmanship

Braided steel, brass, and copper-bronze — every metal in this kit is chosen because it does the job without damaging the barrel. The cable is braided steel under a transparent protective sleeve, with brass knurled connectors at both ends and a weighted pull for a straight, even draw. The bore brush is copper-bronze wire, softer than barrel steel and safe for rifling; the mop is cotton, for a bore cleaner and oil; the patch puller and the brass connector for the screwdriver handle are machined brass. All of it is produced at our own Ningbo plant, running since 2004 with capacity of up to 600,000 brushes a month.

Fig.6 — Alt: Pull-through cable assembly with bore brush and mop for 25 Cal rifle

What's in the Box:

• 1 × Double-ended cleaning nylon brush (large + small heads)

• 1 × Black T-handle (with brass swivel)

• 1 × Bore brush, .25 cal (copper-bronze wire)

• 1 × Cotton mop, .25 cal

• 1 × Screwdriver bit set — 6 pcs (PH1, PH2, 4, 7, T15, T20)

• 1 × Brass patch puller, .25 cal

• 1 × Brass connector for the screwdriver handle

• 1 × 36 in (91 cm) braided steel pull-through cable (transparent sleeve, brass knurled ends, weighted pull)

• 25 × Cleaning patches, 1.5 x 3 in (white)

Fig.5 — Alt: 36-inch pull-through cable with butterfly patch threaded for .25 caliber barrel

How to Use the Pull-Through Cable

Step 1 — Range cleanup. Attach a patch to the 36-inch cable and pull it through the bore once or twice — fouling out in seconds, no bench needed.

Step 2 — Bench detail. Run the .25 bore brush with a bore cleaner, seat patches on the brass puller, then finish with the cotton mop and a light oil coat.

Step 3 — Final check. The 6-piece bit set covers scope-mount and action screws, and the transparent case keeps the 25 Cal Rifle Cleaning Kit with Cable organized and ready.

Always confirm the firearm is unloaded and follow your owner's manual before cleaning.

Factory-Direct from a 20-Year US-Market OEM

Niche calibers rarely make it into the big catalogs — but a factory that has spent 20+ years making brushes for Remington®, Cabela's®, Bulldog®, and Birchwood Casey® can build a proper kit for them. Huntimes is that factory's own brand: the same Ningbo plant (est. 2004; 8 acres; up to 600,000 brushes a month), shipping to the United States, the European Union, and Australia. OEM and private label are welcome — custom contents, custom packaging, and private-label branding are all available; send the quantity and specifications to our sales team for a quotation. For a dealer, that is a niche SKU backed by a full-scale manufacturer.

Frequently Asked Questions

Q1. Which rifles does this kit fit?

A1. The kit is sized for .25 caliber rifle barrels. The bore brush, cotton mop, and brass patch puller are all .25, and the 36-inch cable has the reach for full-length passes on standard hunting rifle barrels, short or long. We do not list specific .25 cartridge names because barrels vary by maker — if you are not sure about your barrel, measure the bore or send us your model before ordering.

Q2. Are the brass, bronze, and steel parts safe for my barrel?

A2. Brass and copper-bronze sit below barrel steel on the hardness scale, which is exactly why they are used here: normal cleaning removes fouling without scratching rifling. The cable runs sheathed through the bore, and the cotton mop applies oil without abrasion. Unload first, follow the manual, and use a bore cleaner before brushing.

Q3. What are the screwdriver bits for?

A3. The six bits handle common rifle hardware: PH1 and PH2 for action and stock screws, slotted 4 and 7 for sight screws, and T15 and T20 for scope-mount fasteners. The brass connector for the screwdriver handle is included in the set. Use the matching bit by hand — these are maintenance tools, not breaker bars.

Q4. Do you offer OEM/ODM and private-label options?

A4. Yes. Our Ningbo factory (est. 2004; 8 acres; up to 600,000 brushes a month) has built cleaning tools for established US brands since 2000. Private label, custom kit contents, and custom packaging are available — send the quantity and specs for a quotation.

Q5. How is the kit packaged, and what are wholesale terms?

A5. Each kit ships in its storage case, components secured inside. Wholesale orders can go in retail-ready boxes, display cartons, or bulk master cartons. MOQ and lead time depend on order size and customization — ask our sales team; we ship to the US, EU, and Australia.

Fig.1 — Alt: 25 Cal rifle cleaning kit in storage case, lid open

Fig.3 — Alt: 25 Cal rifle cleaning kit with pull-through cable and black T-handle, 3/4 view

Fig.2 — Alt: 25 Cal rifle cleaning kit contents arranged in case with bore brush and cable

Fig.4 — Alt: Complete 25 Cal rifle cleaning kit flat lay with bore brush, mop, cable and patches

Fig.7 — Alt: .25 caliber bore brush and mop set for 25 Cal rifle cleaning kit